How to Install a Ghost Immobiliser
A ghost immobiliser guards your vehicle from key cloning or hacking. It works by stopping the engine from starting until a PIN code is entered. This could be as long as 20 characters.
It is unnoticeable by thieves and they are unlikely to expect this extra layer of security. Certain systems have an app which allows the owner to deactivate their immobiliser in the event of forgetting their PIN number or use the service/valet mode.
Connecting the vehicle's CAN Bus
The Ghost 2 Immobiliser is a cutting-edge security system that can be integrated into your vehicle's ECU, providing a discreet line of defence against thieves. It is highly efficient and user-friendly and can be a valuable addition to your vehicle's security arsenal. However, just like any other anti-theft device, it is not 100% reliable and requires regular maintenance to ensure its operation. Fortunately, this guide will assist you in getting the most out of the Ghost 2 Immobiliser.
CAN (Controller Area Network) is a reliable serial network that allows microcontrollers to communicate with each other over short distances without the necessity of a central control unit. It is designed to allow multiplexing of electrical wiring in vehicles to save on copper and comes with a variety of advantages, such as low cost and easy use.
The CAN protocol is utilized in a majority of modern vehicles to communicate with the engine management system, steering control module air conditioning controls and more. It also carries sensor data like speed sensors and inputs to control the various functions of the vehicle. The CAN bus is able to monitor the condition of these different components. It could stop the vehicle from starting when it is in a dangerous condition.
It's important to know how the CAN bus works and how it's secured. It is possible to add new features to a vehicle by using CAN bus, but it's important to secure it against threats from hackers and other types. The best way to achieve this is to install a firewall and monitoring your CAN bus through software.
Ghost2's discreet control unit is concealed in the wiring harness or dashboard, eliminating the possibility of a burglar physically tampering with it. It is also impossible to reset a pin code or emergency code without access to the vehicle.
If you have to give your car away to a valet parking service, maintenance or for any other reason, you can activate the Transport Mode. This feature disables the Ghost immobiliser's keyfob and ignition functions, and will only reactivate when the car reaches 31 mph for 15 minutes.
Making a PIN code
The Ghost immobiliser is an effective security device that shields your vehicle from theft. The innovative technology uses a PIN to shut down the vehicle's engine and prevent it from starting without the right code, or a valid fob/mobile. The system's subtle design makes it unnoticeable, and offers unrivaled protection against theft. The system is TASSA-verified and can save you significant sums on your car insurance.
During the installation when you install the Ghost system enters the learning mode to record the sequence of buttons that are pressed to create your unique pin code. Once the pin code has been created and the installer has completed its work, it will guide you through the steps to activate the system. Once activated by the system, the Ghost system will disable the starter motor of your vehicle until a valid PIN has been entered or the vehicle is switched into transport mode. This makes it very difficult for thieves or cloners who want to hack or replicate your starter system.
Installing an Ghost immobiliser is simple however it is essential to follow the specific instructions in the user's manual to ensure proper operation. Hand tools are essential in making accurate connections and a multimeter can help you verify electrical values. Insulation tape as well as heat shrink tubing and cable ties are a good option to protect exposed wiring. Also, be sure to check the system regularly to identify any problems and potential mistakes.
It is important to test the system one more time prior to turning on the ignition. Ghost immobilisers are able to rearm themselves after 3 to 30 seconds depending on the model of the vehicle. The system also has a Service/Valet mode that allows you to temporarily remove the system for servicing your vehicle or valet parking.
Idealy, the immobiliser will be hidden under the dashboard or on the steering wheel. It is recommended to use a small bit of duct tape or paint to mark the CAN H and L wires, so that you can easily find them during testing. Additionally the CAN H and CAN L wires should be connected to a power source that has continuous 12V. It is essential to test the connections after testing, as an the incorrect identification of these wires could cause the system to malfunction.
Invoking the system
A ghost immobiliser stops your car from starting unless you press a sequence of buttons inside the car, usually the steering wheel, door panel, or central console. ghost vehicle immobiliser is decided by the user and can be changed if necessary. Once activated, the system will not be removed. This makes it a great choice for anyone who wants to secure their vehicle from theft.
The system is designed to be undetectable, which means it isn't detected by modern diagnostic tools or code-grabbing technology. It doesn't emit radio frequency either, making it even more difficult for thieves find.
If the device is found it will stop the engine from running. It will also sound an alarm to scare thieves away. The device can be used to monitor a car's location which can help police recover the vehicle if it has been taken.
Contact Car Specalist Customs for a estimate or to discuss your options in Ghost immobiliser. We are fully trained to install a ghost immobiliser for your vehicle and will make sure it is concealed in a hard-to-reach area. We can also provide other security measures such as a wheel lock and kill switch to help protect your vehicle from thieves.
Disarming the System
If you have a Ghost immobiliser fitted to your vehicle, it's important to know how to disarm it. This will help you in the event that you lock your keys in the car or when your battery goes out of. The system uses an individual PIN code that only you know, which means the immobiliser will not start your car without entering this code. The easiest way to enter the code is to press a set of buttons on your dashboard or steering wheel. This is a far simpler method than using the key fob and also stops anyone from copying your remote.
Ghost2 is not intrusive unlike some aftermarket immobilisers which require cutting wires for installation. It also integrates with the CAN bus system of your vehicle in order to function. Its most distinctive feature is that it shuts off the engine without affecting normal functions of the vehicle. This makes it very difficult for thieves to use signal boosters or duplicate keys to car keys. Furthermore, it doesn't emit radio frequencies, meaning thieves can't detect the system.
The Ghost system also has the Transport Mode that allows you to temporarily disable the security system for situations such as transportation or servicing. This is an excellent option if you have to lend your vehicle to a person who isn't sharing the PIN code, or if you wish to secure your vehicle while driving it. To activate the Transport Mode, press the service button five times within a period of 2 seconds. The Ghost system will confirm activation via five indication signals.
Keep the emergency code inside your vehicle in a secure location. In the event that you discover yourself locked out of your vehicle, you can contact the technician or the company who installed the system and they'll provide you with the code. If you cannot reach them You can always try contacting an authorized dealer however this will require verification procedures and could result in additional fees.
Apart from the ease of this system, you can also count on it to guard your car against theft and cut down on insurance costs. Many insurance companies offer reduced monthly rates or even financial incentives for installing this anti-theft device.